Question

Find out the transfer function

Tagged in

Engineering

Electrical Engineering

Find answers to questions asked by students like you.

Q: A 4 pole 250 volt shunt motor gives 10kw when running at 1000 rpm and drawing armature and field cur...

A: Given values are - P=4Vt=250VoltN=1000rpmIa=60AISh=1ARa=0.2Ohm Given motor is shunt motor.

Q: (1) A full adder in which: SUM = C' (AB' + A'B) +C (AB + A'B') (2) CY = AB + BC + AC

A: The truth table for the given full adder is given as A B C Sum Carry 0 0 0 0 0 0 0 1 1 0 0...

Q: How far must mechanical protection be provided when underground service conductors are carried up a ...

A: The Underground Conductor are electric conductor insulated and placed under the surface of the earth...

Q: O:28)

A: Part (a): Consider the open-loop transfer function, Gs=s2-2s+4s+5=s-1+j1.73s-1-j1.73s+5 The number o...

Q: what is the power absorbed of two identical resistors are connected in series to 10v source. one res...

A: Given: Two identical resistors with resistance 2-ohms each is connected in series. Source voltage, V...

Q: Lightning strikes a dielectric sphere of radius 15 mm for which e, =4.5, o 5 x 10- S/m and deposits ...

A: Click to see the answer

Q: For the circuit in Figure 1, and the 9 V source supplies a current of 7.6 A (that is, a current of ...

A: Here we will apply Nodal analysis to find out the unknown parameters. => In nodal analysis we co...

Q: A 20-ohm resistor and a capacitor are connected in series with a battery of 60 volts. At t 0, there ...

A: Click to see the answer

Q: Emitter stabilized polarization BJT DETERMINE, FIND: a. IBQb. ICQc. VCEQd. Vce. VBf. VE

A: Click to see the answer

Q: A 400V, 50Hz 30hp three-phase induction motor is drawing current at power factor 0.8 lagging. The ...

A: The given information of the motor:

Q: a) Construct a circuit model for this device using an ideal voltage source and a resistor.

A: (a)

Q: Consider the circuit shown in Figure 1. Vcc= +12 V (DC), R1 = 100KΩ, R2 = 10 KΩ, RE = 1KΩ and RL = 2...

A: To find all the circuit parameters given the circuit can be modified as From the figure we have

Q: 4- If we have a signal f(t) passing through a system with impulse response g(t), the output is (b) g...

A: Convert the functions in the Laplace transform, and find the output. f(t)→LFsg(t)→LGsYs=FsGs

Q: Find the Laplace transforms of the following time functions. using the Laplace transform definition ...

A: Click to see the answer

Q: In the circuit given below, R = 10 Ω. Find vo using mesh analysis. The value of vo in the circuit i...

A: d

Q: 4. Indicate if the power thyristor will be on or off under the following conditions: The thyristor w...

A: Click to see the answer

Q: Find I and V in the given circuit. Assume A = 4 A, B = 11 A, and C = -5 A. The current and voltage...

A: Click to see the answer

Q: Q:22)

A: Click to see the answer

Q: Answer the following questions: i. If a 3-input XOR gate has eight input possibilities, how many of ...

A: (i) 3 input X-OR gate symbol present as, Where output, w=x⊕y⊕z

Q: a sine wave has a maximum value of 230 v. what is the voltage after 38° of rotation

A: Click to see the answer

Q: 2 A sequential circuit has two JK flip-flops A and B and one input x . The circuit is described by t...

A: Click to see the answer

Q: 4.2 Use the node-voltage method to find v in the circuit shown. 6 N 20 4Ω 4.5 A $10 12N (*) + 30 V

A: Click to see the answer

Q: In the circuit given below, R = 110 Ω. Find the value of io using mesh analysis. The value of io ...

A: Consider the voltage across the current is vo. The circuit diagram in which the current is mentione...

Q: Vdd value is 12V. Figure 1 Problem 2: Determine the following for the network of figure 2 given that...

A: Click to see the answer

Q: Determine the currents I1, I2 and Iz for the electrical network shown in the following figure:

A: Write KVL in both loops, 50-5I1-20I3=0 .....130+20I3+10I2=0 ......2 ...

Q: R:57)

A: X1 is the overlap angle μVs=Vmsin ωtVs=2202 sin ωtVm==2202 ∆Vd0 = The average voltage reduction due ...

Q: A dc power supply is to be developed by employing an ac to dc converter as a power processing conver...

A: According to question: The suitable rectifier for above power processing will be single phase semi-c...

Q: 1. The current entering the positive terminal of a device is, i = 2e-2t (A) and the voltage across t...

A: Click to see the answer

Q: In the circuit given below, V = 174 V. The variable resistor is adjusted until it absorbs maximum po...

A: As per maximum power transfer theorem, maximum power absorbed by load resistor if the load resistanc...

Q: an overhead transmission line has a span of 220 meters the conductor waiting 0.604 kg/m.What will be...

A: Given: Span, L=220 m Weight of conductor, w=0.604 kg/m Tension, T=2879 kg

Q: b) Obtain the output expression Y for the circuit given in Figure 2 (Write the output of each gate)....

A: Click to see the answer

Q: Determine IB RC 100 Ω RB + Vcc 10 V 10 kΩ VBB 5 V

A: Click to see the answer

Q: a) Determine the number of mesh-current equations needed to solve the circuit shown. 4.8 b) Use the ...

A: Given circuit,

Q: Write one paragraph describing why you think chrome has a shiny surface.

A: Most metals are shiny like chrome when you polish them. However, they usually quickly oxidize when t...